ERV vs. HRV: Which Ventilator Fits Your Utah Home?

An HRV (heat recovery ventilator) moves only heat between outgoing stale air and incoming fresh air. An ERV (energy recovery ventilator) moves heat and a share of moisture. For most homeowners the choice comes down to how humid your outdoor air gets, how many people and how much cooking, showering and plant life add moisture inside, and how tight the house is. The tighter you build or seal, the more you need one of them. That is why we plan ventilation together with air sealing and insulation, in the design phase of a new build, an addition or a major remodel, not after the walls are closed.
TL;DR
- An HRV transfers heat only. An ERV transfers heat and some water vapor, so it keeps indoor humidity steadier through the seasons.
- Manufacturers generally point HRVs to cold or dry climates and ERVs to humid ones. Your household’s moisture load can tip the choice either way.
- Neither unit is a dehumidifier. Both recover roughly 70% to 80% of the energy in exhaust air in most systems.
- Air sealing makes a house tighter, and a tight house needs controlled ventilation. Seal first, test with a blower door, then ventilate on purpose.
- The best time to settle all of this is before drywall, in the same plan as your insulation, windows and HVAC.
Table of Contents
- What an ERV and an HRV actually do
- How much energy do they recover?
- How to choose: climate, people and airtightness
- Do you still need a dehumidifier with an ERV?
- Sizing: what a 2,000-square-foot house needs
- Air sealing, insulation and ventilation work as a set
- Where ventilation shows up in a build or remodel
- Perspective
- Plan ventilation into your project with us
- FAQ
- Sources
What an ERV and an HRV actually do
A modern, well-sealed house does not breathe on its own. Stale air, cooking odors, humidity and the gases that building materials give off stay inside unless something moves them out. A balanced ventilation system does that job. It brings in fresh outside air while exhausting an equal amount of stale air, so the house stays at neutral pressure, and the two airstreams pass through a core where heat moves from the warmer stream to the cooler one.
That core is the whole difference:
- HRV: the core passes heat only. In winter the outgoing air preheats the incoming air. In summer the cooler indoor air pre-cools the hot incoming air.
- ERV: the core passes heat and water vapor. The DOE’s Building America guidance says the ERV’s exchanger transfers water vapor along with heat, which helps keep indoor humidity more constant.
The Home Ventilating Institute describes the direction of that moisture swap. In cold weather, moisture moves from the exhaust stream to the fresh stream, so the house does not dry out as much. In warm, humid summers, it moves from the fresh stream to the exhaust stream, so less outdoor humidity enters.
There is a practical difference in the hardware too. According to Canada Mortgage and Housing Corporation, condensation forms in HRV cores, which is why they have drain pans, and cores can freeze in very cold temperatures, which is why they have defrost dampers. ERV cores use materials that pass moisture as well, so condensation does not typically form in them. If a unit is going into a cold mountain location, ask how it handles defrost and where the condensate drains.
How much energy do they recover?
Both types are about recovering energy you have already paid to heat or cool. The U.S. Department of Energy says energy recovery ventilation lowers winter heating costs and summer cooling costs by conditioning incoming air with the outgoing air. PNNL’s whole-house ventilation guide reports that most ERVs recover about 70% to 80% of the sensible energy in the exiting air, and that they perform best at peak outdoor conditions and lose some efficiency in cold, humid weather.
Fine Homebuilding puts the numbers side by side: HRV sensible heat recovery averages about 70% and can reach 95%, while ERV latent (moisture) recovery is usually 40% to 60%. Read those as two different measurements. The HRV figure is about heat. The ERV’s moisture figure is an extra service on top of its heat recovery.

How to choose: climate, people and airtightness
There is no single winner. Three questions decide it.
1. What is your outdoor air like?
Building Science Corporation notes that manufacturers typically recommend HRVs for cold (heating-dominated) or dry climates and ERVs for humid climates. Health Canada adds that to avoid excessive indoor humidity in summer, an ERV is preferable to an HRV.
For homes in Washington and Iron Counties, the practical picture is hot summers and a mostly dry climate, with colder winters as you gain elevation toward Cedar City. In that kind of cooling-dominated, dry setting, the summer benefit of an ERV is that it limits how much warm, moist outdoor air it pulls in during monsoon-season humidity spikes. That also reduces the load on your air conditioner. Health Canada says an air-conditioned house with windows closed can exceed the recommended indoor humidity of under 50% by bringing in warm, moist air, and that an ERV reduces the cooling and dehumidification workload in that case.
2. How much moisture do you make indoors?
This is the question most comparison pages skip. BC Housing states that in houses with a lot of moisture from high occupancy, pets, plants or frequent cooking, an ERV may put too much moisture back into the house, and an HRV may be more appropriate. The reverse also holds. Building Science Corporation says a large, leaky, low-occupancy house with an HRV in a cold climate can end up with uncomfortably low humidity, and Health Canada says an HRV can dry a house out in winter.
A quick way to think about your household:
| Your situation | Leans toward |
|---|---|
| Hot summers, air conditioning running for months, moderate occupancy | ERV |
| Large house, few occupants, dry winters | ERV (keeps some moisture in) |
| Many occupants, lots of cooking and showering, cold winters | HRV (moves moisture out) |
| Humid summers and a big household | Either one, plus a plan for a dehumidifier |
Treat the table as a starting point for a conversation about your plans, not a verdict. Your floor plan, kitchen and bathroom layout and equipment sizing all change the answer.
3. How tight is the house?
Airtightness is what makes ventilation necessary. BC Housing says houses at roughly 3 air changes per hour at 50 pascals (ACH50) or tighter generally need continuous mechanical ventilation for adequate indoor air quality. A new custom home built to current energy standards is normally well inside that range. An older home you have just air sealed may be too.
Do you still need a dehumidifier with an ERV?
This is one of the most common questions, and the honest answer is that an ERV is not a dehumidifier. Building Science Corporation states that ERVs do not dehumidify or cool the interior in summer, and that where humidity is a problem, separate dehumidification is needed. What an ERV does is stop the problem from getting bigger by limiting how much moisture comes in. Fine Homebuilding’s Scott Gibson makes the same point: many homes in humid summers still need a separate dehumidifier alongside the ERV.
For the dry climate of most of southern Utah, many households will find the air conditioner handles summer comfort on its own. If you plan a finished basement or a basement ADU, where moisture behaves differently from the rest of the house, bring humidity control into the design conversation early.
Sizing: what a 2,000-square-foot house needs
Ventilation is sized to the number of bedrooms and floor area, not the equipment catalog. Fine Homebuilding reports that a three-bedroom, 2,000-square-foot house typically needs a 90 to 100 CFM system to meet the ASHRAE 62.2 ventilation standard. CFM means cubic feet per minute, the volume of air the unit moves. ASHRAE 62.2 is the national residential ventilation standard that building codes and efficiency programs commonly reference.
Three things move that number up or down:
- Bedrooms and occupants. The standard adds airflow for each bedroom.
- Floor area. More square footage means more required airflow.
- Leakiness. In a tighter house, the ventilator carries nearly all of the fresh air, so it matters more.
Oversizing wastes energy and undersizing leaves stale air. Ducts matter just as much as the unit. A system with long, undersized or leaky duct runs will not deliver the airflow printed on the box. CSU Extension points out that ductwork can be added to a home that lacks it, but the cost may be prohibitive. A single-room “spot” ERV is an alternative for one space. In a new build or a gut remodel, running ducts costs far less because the walls and ceilings are already open.
Air sealing, insulation and ventilation work as a set
Several related searches ask how air sealing differs from insulation. Here is the short version.
Air sealing closes the gaps and cracks between your living space and the outdoors or the attic and crawlspace. CSU Extension describes it as reducing drafts and energy use, and notes that most insulation types, apart from foam and very densely blown-in loose fill, still let air pass through. Insulation slows heat moving through materials. A wall can be full of insulation and still leak at the top plate, at wiring penetrations and around windows. Sealing the air path and insulating are two jobs.
The order matters. The DOE Home Improvement Expert fact sheet says to ensure effective ventilation before increasing airtightness, to control moisture before adding air sealing and insulation, and to capture air-sealing opportunities before insulation goes in. The same sheet calls sealing uncontrolled leaks one of the most cost-effective home performance measures, because it cuts heating and cooling bills, drafts, and the dust, pollen and moisture that leak in.
In practice:
- Measure first. A blower door test depressurizes the house with a calibrated fan so leaks can be found and the total leakage measured. The DOE fact sheet recommends testing with a blower door, following RESNET standards, before work begins and setting a target level. Health Canada likewise recommends measuring airtightness before retrofitting a ventilation system. We cover the process and how to read the numbers in our guide to the blower door test.
- Seal the leaks the test finds, starting with the attic plane, rim areas, penetrations and ducts.
- Insulate once the air barrier is in place.
- Retest and size the ventilation to the tightness you actually achieved.
What does air sealing cost?
There is no honest flat price, because the work depends on house size, age, how accessible the attic and wall cavities are, and how many leaks the test turns up. The test itself is easier to price: a national 2026 estimate from Angi puts a single-family blower door test at $200 to $450. Sealing is normally priced from the test findings and the scope of work. When air sealing is done as part of an addition, kitchen expansion or remodel, it is far cheaper than as a stand-alone retrofit, since the surfaces are already open.
Where ventilation shows up in a build or remodel
Ventilation is not one box in the garage. It touches several parts of a project, which is why it helps to have one team looking at all of them:
- New custom homes. The ventilator, ducts, air barrier and insulation can be designed as a system from the start. See our notes on energy efficient home upgrades for how these pieces pay back.
- Kitchens. A strong range hood exhausts air, and the house has to replace it. Our guide to kitchen ventilation options explains ducted and recirculating choices, and our energy efficient kitchen remodel guide covers what to upgrade first.
- Bathrooms. Spot exhaust fans remove shower moisture at the source, and local rules decide what is permit-ready. Our page on bathroom ventilation requirements walks through them.
- Attics and exteriors. Sealing and insulating the attic and choosing windows and shade work alongside ventilation. See our look at a radiant barrier in the attic and our guide to desert home efficiency.
- Additions and ADUs. A new bedroom, family room or casita changes the house’s volume and occupancy, which changes the ventilation math.
Perspective
When a family tells us they want an energy-efficient home, they usually mean lower bills and a comfortable house. Ventilation rarely comes up until we raise it, even though it decides whether a tight house feels fresh or stuffy.
Our view is that the ERV-versus-HRV question is a design question, not a shopping question. The right answer depends on the floor plan, the number of people, how you cook, where the air conditioning and ducts run, and how tight the envelope ends up. That is why we keep design and construction under one roof, with a single point of contact for both. When the person drawing the kitchen is the same one coordinating the framing and the mechanical work, the ventilation plan does not get lost between trades.
We also lean on tools that let you see decisions early. Virtual consultations and 3D renderings let us walk through where ducts, returns and fixtures go before anything is built, so there are fewer surprises and a clearer budget.
Jake
Plan ventilation into your project with us
If you are building a custom home in Washington or Iron County, or opening up walls for an addition or a major remodel, that is the moment to settle air sealing, insulation and ventilation together. We offer custom home construction and room additions, both with design and construction handled through one point of contact and a clear, itemized process from planning to completion.

Tell us about your project through our website and we will start with your floor plan, your household and your comfort goals.
FAQ
Is an ERV better than an HRV?
Not universally. An ERV suits hot or humid summers and homes with moderate moisture, because it limits how much outdoor humidity comes in and keeps indoor humidity steadier. An HRV can suit cold climates and busy households that generate a lot of moisture, since it does not return moisture to the house. The decision depends on climate, occupancy and airtightness together.
What are the disadvantages of an ERV system?
The main thing to plan for is moisture. An ERV does not dehumidify, so homes with humidity problems may still need separate dehumidification. In a small, tight, high-occupancy house in a cold climate, it may not remove enough winter moisture, which can cause window fogging. Choosing the right type and size at the design stage avoids this.
What size ERV do I need for a 2,000-square-foot house?
A three-bedroom, 2,000-square-foot house typically needs about 90 to 100 CFM to meet ASHRAE 62.2, according to Fine Homebuilding. Bedroom count, floor area and how tight the house is all adjust that figure, so size it from your actual plans and test results.
Should I air seal before installing an ERV or HRV?
Yes, in most projects. Measure leakage with a blower door, seal what it finds, and then size the ventilator for the tightness you reach. The DOE fact sheet also says to make sure ventilation is effective before you increase airtightness, so the two steps belong in one plan.
Sources
- Building America Best Practices Series, Vol. 10: Retrofit Techniques and Technologies, Air Sealing (U.S. DOE)
- DOE Home Improvement Expert Fact Sheet: balanced ventilation (PNNL)
- DOE Home Improvement Expert Fact Sheet: home air sealing (PNNL)
- Heat Recovery and Energy Recovery Ventilators: A Guide (CMHC)
- HVAC Energy Recovery Ventilation (Building Science Education, U.S. DOE)
- Continuous Whole-House Ventilation (Home Ventilating Institute)
- Whole-House Ventilation Strategies for New Homes (PNNL)
- Choosing Between HRVs and ERVs (Fine Homebuilding)
- BSC Information Sheet 611: Balanced Ventilation Systems (Building Science Corporation)
- Ventilation and the Indoor Environment (Health Canada)
- Heat Recovery Ventilation: Houses (BC Housing)
- Air Sealing Colorado Homes (CSU Extension)
- How Much Does a Blower Door Test Cost? (Angi)
Recommended
Images in this article are editorial illustrations, not Prestigious project photography.
